mangavalk

mangavalk pushed to main at mangavalk/planar-EL512.256-H

2026-10-19 17:57:26 +02:00

a4ce97d744 Divergence meter: keep digits inside the tubes, close the domes

mangavalk pushed to main at mangavalk/planar-EL512.256-H

2026-10-19 16:46:31 +02:00

d2e81a5a36 Add a PC renderer for the themed pages; fix overlapping layouts

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 16:34:26 +02:00

a63b66a7d8 bdp_guard: new zero at every ARM

mangavalk pushed to main at mangavalk/planar-EL512.256-H

2026-10-19 16:29:29 +02:00

13a499fd97 Add four Star Trek / Lower Decks pages with a 3D printer red alert

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 16:29:02 +02:00

29604b2f1e PA calibration: wider PA range for TPU/TPE

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 16:15:03 +02:00

8a5f6b6dd9 PA calibration: lower test flow for TPU/TPE

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 16:04:40 +02:00

93ae8795b8 PA calibration reads Spoolman first; guard resets a sensor left in PA mode

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 16:00:36 +02:00

d49e65c0bb Flexible lanes load slower; purge at the previous filament's temperature

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 15:20:03 +02:00

464a7c1046 CLAUDE.md: purge check peaks up to 246 with ASA at 250-260C

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 14:26:21 +02:00

0b1b2a6947 Purge check: accept load-check firmware v2; chamber load levels first

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-18 23:25:27 +02:00

b9d2f3a062 Nozzle guard in stop mode (brush log-only), wait for the nozzle before HOME

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-18 23:11:00 +02:00

a16b57a0a9 Move bd_pressure.cfg and TEST_SPEED into the repo

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-18 23:06:47 +02:00

8eef0ee298 bdp_guard: one lock for all I2C transfers of the bd_pressure

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-18 22:56:56 +02:00

61fa8acb05 Print start: contact homing, nozzle guard, Z check, purge before chamber heat

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-17 19:57:28 +02:00

2100857846 Chamber prints: unload a lane that is not the first tool before the soak

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-17 19:46:23 +02:00

6cc43f951d Print start: soak before QGL and Z, load after Z, PA per lane temperature

e5be65834e LEDs: nozzle light follows the motion sensor, new logo status macro

Compare 2 commits »

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-16 17:41:59 +02:00

fbdb2d5e1d Show errors and warnings on the display (_ERROR, _WARN)

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-15 22:13:39 +02:00

a67e99015f RESUME: check the AFC lane, add AFC_CLEAR_ALL_MESSAGES

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-14 15:19:38 +02:00

ec1f67e455 PA_CALIBRATE_ALL_LANES: skip lanes without filament

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-12 21:18:23 +02:00

536db5836d Purge check: fail when bd_pressure does not answer, add override