mangavalk

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 16:04:40 +02:00

93ae8795b8 PA calibration reads Spoolman first; guard resets a sensor left in PA mode

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 16:00:36 +02:00

d49e65c0bb Flexible lanes load slower; purge at the previous filament's temperature

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 15:20:03 +02:00

464a7c1046 CLAUDE.md: purge check peaks up to 246 with ASA at 250-260C

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-19 14:26:21 +02:00

0b1b2a6947 Purge check: accept load-check firmware v2; chamber load levels first

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-18 23:25:27 +02:00

b9d2f3a062 Nozzle guard in stop mode (brush log-only), wait for the nozzle before HOME

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-18 23:11:00 +02:00

a16b57a0a9 Move bd_pressure.cfg and TEST_SPEED into the repo

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-18 23:06:47 +02:00

8eef0ee298 bdp_guard: one lock for all I2C transfers of the bd_pressure

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-18 22:56:56 +02:00

61fa8acb05 Print start: contact homing, nozzle guard, Z check, purge before chamber heat

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-17 19:57:28 +02:00

2100857846 Chamber prints: unload a lane that is not the first tool before the soak

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-17 19:46:23 +02:00

6cc43f951d Print start: soak before QGL and Z, load after Z, PA per lane temperature

e5be65834e LEDs: nozzle light follows the motion sensor, new logo status macro

Compare 2 commits »

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-16 17:41:59 +02:00

fbdb2d5e1d Show errors and warnings on the display (_ERROR, _WARN)

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-15 22:13:39 +02:00

a67e99015f RESUME: check the AFC lane, add AFC_CLEAR_ALL_MESSAGES

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-14 15:19:38 +02:00

ec1f67e455 PA_CALIBRATE_ALL_LANES: skip lanes without filament

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-12 21:18:23 +02:00

536db5836d Purge check: fail when bd_pressure does not answer, add override

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-12 21:10:09 +02:00

25891640b8 Reject PA calibrations with no result or bad sensor data

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-12 19:46:38 +02:00

82f9486160 README: remove the section on switching from config folder copies

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-12 18:18:39 +02:00

93f00c87a7 Stop using bdwidth while printing, work without it

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-12 18:03:27 +02:00

76172fbc4f Remove committed __pycache__, ignore Python bytecode

e4d2230a57 bdwidth_status: keep a bdwidth USB dropout from shutting down Klipper

Compare 2 commits »

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-12 14:09:32 +02:00

eb7e0d4482 Purge and check before resuming after a PAUSE

mangavalk pushed to main at mangavalk/klipper-macros

2026-10-11 20:32:08 +02:00

b6379621f6 bdwidth: width only in PRINT_START