nixie-clock/firmware/uniclock/ESP32_UniClock2/nixie595.ino

// ============================================================================
// Nixie driver: two cascaded 74HC595s on hardware SPI, multiplexed anodes
// ----------------------------------------------------------------------------
// Hardware: RetroModding NixieIN12v2 (CLOCK_90). The two 595s hold one 16-bit
// word that drives the whole display:
//   bits 0..9    cathodes for digits 0..9 (via 2x ULN2003, shared by all tubes)
//   bits 11..14  tube anodes (anodeBits[] in clocks.h), one tube at a time
//   bits 10, 15  neon dots P1/P2 (NEON_BITS in clocks.h)
// The high byte is shifted out first (ends up in the second 595), MSB first.
// DATA and CLOCK are the HSPI MOSI/SCK pins (GPIO13/GPIO14), PIN_LATCH is the
// 595 storage clock. Pinout and bit map come from the stock firmware, see
// docs/stock-firmware-pins.md in the nixie-clock repo.
//
// The multiplex ISR writes the SPI1 and GPIO registers directly instead of
// calling the SPI library, so it runs entirely from IRAM and keeps refreshing
// while the flash cache is off (EEPROM/SPIFFS writes, OTA).
//
// Platform: ESP8266 ONLY (timer1 + SPI1 registers). The ISR state machine
// (brightness by blanking time, animMask wipe) follows multiplex74141.ino.
// ============================================================================
#ifdef NIXIE595_MULTIPLEX
#include <SPI.h>
char tubeDriver[] = "NIXIE595_MULTIPLEX";

#if !defined(ESP8266)
  #error "NIXIE595_MULTIPLEX is for ESP8266 only!"
#endif

int maxDigits = sizeof(anodeBits);  //anodeBits is byte[], so sizeof == element count
int maxDig = maxDigits;

// timer1 runs at TIM_DIV16 = 5 MHz (0.2 us per tick): 11000 ticks = 2.2 ms per tube slot,
// about 110 Hz for 4 tubes. PWM_min/PWM_max are the lit part of a slot (brightness).
// const, so the ISR's static locals are constant-initialized (no flash-resident init guard).
const int PWMrefresh = 11000;
const int PWM_min = 1000;
const int PWM_max = 10000;

// Shift one 16-bit word into both 595s and latch it. Also called from main code via clearTubes(),
// so the caller must keep the ISR out (see clearTubes()).
static inline void IRAM_ATTR write595(uint16_t w) {
  while (SPI1CMD & SPIBUSY) {}
  SPI1W0 = (w >> 8) | ((w & 0xFF) << 8);  //SPI1W0 byte 0 goes out first: high byte first
  SPI1CMD |= SPIBUSY;
  while (SPI1CMD & SPIBUSY) {}
  GPOS = 1 << PIN_LATCH;   //rising edge copies the shift registers to the outputs
  __asm__ __volatile__("nop; nop; nop; nop;");
  GPOC = 1 << PIN_LATCH;
}

void setup_pins() {
  DPRINTLN("Nixie clock - setup pins -  74HC595 multiplex mode...");
  pinMode(PIN_LATCH, OUTPUT);
  digitalWrite(PIN_LATCH, LOW);
  regPin(PIN_LATCH, "PIN_LATCH");

  SPI.begin();   //HSPI: GPIO14 = SCK, GPIO13 = MOSI. It also claims GPIO12 (MISO), which the NeoPixel setup takes back later.
  SPI.setFrequency(SPI_FREQ);
  SPI.setBitOrder(MSBFIRST);
  SPI.setDataMode(SPI_MODE0);
  regPin(13, "PIN_DATA (HSPI MOSI)");
  regPin(14, "PIN_CLK (HSPI SCK)");
  //16-bit transfers, so one write fills both 595s
  SPI1U1 = (SPI1U1 & ~((SPIMMOSI << SPILMOSI) | (SPIMMISO << SPILMISO)))
           | (15 << SPILMOSI) | (15 << SPILMISO);
  write595(0);   //all anodes, cathodes and dots off

  DPRINT("Tubes: "); DPRINTLN(maxDigits);
  startTimer();
}

void IRAM_ATTR writeDisplay() {   //timer1 ISR, single-shot: must re-arm timer1 at the end of every call
  static byte pos = 0;
  static byte state = 0;
  static int timer = PWMrefresh;
  static byte num;
  static int brightness;
  static int PWMtimeBrightness = PWM_min;
  uint16_t w;

  if (EEPROMsaving) {   //keep the tubes dark while settings are written
    write595(0);
    timer1_write(PWMrefresh);
    return;
  }

  intCounter++;
  brightness = displayON ? prm.dayBright : prm.nightBright;
  if (brightness > MAXBRIGHTNESS) brightness = MAXBRIGHTNESS;  //only for safety

  timer = PWMrefresh;

  // Same state machine as multiplex74141.ino:
  //  state 0: next tube; show the old digit (animation) or the current digit
  //  state 1: show the new digit for the rest of the lit time (only while animating)
  //  state 2: blank for the rest of the slot (this sets the brightness)
  //  state 3: blank output, then back to state 0
  switch (state) {
    case 0:
      pos++;
      if (pos > maxDig - 1) {
        pos = 0;
        if (autoBrightness && displayON)
          PWMtimeBrightness = max(PWM_min, PWM_max * lx / MAXIMUM_LUX);
        else
          PWMtimeBrightness = max(PWM_min, PWM_max * brightness / MAXBRIGHTNESS);
      }
      if (animMask[pos] > 0) {
        num = oldDigit[pos];
        timer = (PWMtimeBrightness * (20 - animMask[pos])) / 20;
        state = 1;
      }
      else {
        num = digit[pos];
        timer = PWMtimeBrightness;
        state = 2;
      }
      break;
    case 1:
      num = newDigit[pos];
      timer = (PWMtimeBrightness * animMask[pos]) / 20;
      state = 2;
      break;
    case 2:
      timer = PWMrefresh - PWMtimeBrightness;
      state = 3;
      break;
  }
  if (timer < 500) timer = 500;  //a too short timer1 reload can miss the interrupt

  if ((brightness == 0) || (state == 3) || (!radarON)) {
    state = 0;
    w = 0;
  }
  else {
    w = 0;
    if (num <= 9) w |= 1 << num;   //cathode; 10 = blank, other glyphs are not available on a Nixie
    if ((pos == NEON_POS) && colonBlinkState) w |= NEON_BITS;
    if (w) w |= 1 << anodeBits[pos];
  }
  write595(w);

  timer1_write(timer);
}

void clearTubes() {
  noInterrupts();   //the ISR also writes the 595s
  write595(0);
  interrupts();
}

// Not needed: the ISR refreshes the display continuously (same as multiplex74141.ino).
void writeDisplaySingle() {}
#endif