patriandClaude Opus 5.5
be69bda4f1
- ATRV every 2 s; voltage arc in the bottom gap (11-15 V) + number, colored by state (low / weak / resting / charging / overcharge) - idle after Off/2/5/10 min without speed data (settings page, NVS): screen off, GIF paused, OBD polling stopped, ATRV every 30 s; wakes on touch (swallowed by a top-layer overlay) or > 13.2 V - status pill moved up to make room for the voltage Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
37 lines
2.7 KiB
Markdown
37 lines
2.7 KiB
Markdown
# OBD Speed (JC3636W518)
|
||
|
||
Vehicle speed from an ELM327 over BLE, shown as a big number + arc gauge on top of an animated GIF.
|
||
Uses the shared board library and LVGL 9.6 (`../shared`), NimBLE-Arduino 2.5.1.
|
||
|
||
## Use
|
||
- **Speed page** — speed in km/h (`--` = no data: not connected, or ignition off), arc gauge 0–200 km/h,
|
||
status pill below the number (adapter name when running, otherwise what it is doing).
|
||
**Battery voltage** (`ATRV`, every 2 s) as a small arc in the bottom gap (11–15 V) + number; color:
|
||
red < 11.8 V, orange < 12.2 V, green < 13.0 V (resting OK), blue ≤ 14.8 V (charging), red above (overcharge).
|
||
- **Swipe left → adapter menu** — scans while open. OBD-like adapters (name OBD/ELM/…, or service FFF0/FFE0/18F0)
|
||
are listed first in green. **Tap one** to select it: it is remembered (NVS) and connected immediately.
|
||
**Forget** clears the remembered adapter, **Done** (or swipe right) returns to the speed page.
|
||
- **Swipe left again → settings** — screen rotation 0 / 90 / 180 / 270 degrees, and **screen off without data** Off / 2 / 5 / 10 min (default 2). Both remembered in NVS.
|
||
- **Idle** — after that time without speed data (ignition off, adapter gone) the screen goes dark, the GIF pauses and
|
||
OBD polling stops; only `ATRV` every 30 s (answered by the adapter itself, doesn't wake the car's bus).
|
||
Wakes on a touch (the touch is swallowed) or by itself when the voltage rises above 13.2 V (engine started).
|
||
Not used while no adapter is chosen.
|
||
- On power-up the remembered adapter is connected automatically; if the link drops or the adapter is not
|
||
there (car off), it retries every 3 s. With no adapter remembered, the device starts on the menu page.
|
||
|
||
## How it talks to the ELM327
|
||
Service `FFF0`, notifications + commands on `FFF1` (verified with the user's "OBDII" adapter, see
|
||
`docs/2026-10-23_ble_scanner_car_test.txt`, made with the BLE scanner tool that was removed afterwards — in git history); other adapters: first notify+write pair.
|
||
Init: `ATZ`, `ATE0`, `ATL0`, `ATS0`, `ATH0`, `ATSP0`, `0100`; then `010D` (speed) is polled continuously.
|
||
Serial (115200) prints status changes as `[obd] ...`.
|
||
|
||
## Files
|
||
| File | What |
|
||
|---|---|
|
||
| `src/main.cpp` | LVGL UI (tileview: speed page + menu page) |
|
||
| `src/obd_link.cpp/.h` | BLE scan, connect/reconnect, ELM327 init and speed polling (background task on core 0) |
|
||
| `src/font_speed_120.c` | Montserrat Medium 120 px, digits and `-`, 4 bpp (generated with `lv_font_conv`, see header) |
|
||
| `data/bg.gif` | Background (`ezgif-5-cb56986bc7.gif`, 360×360), linked into the firmware via `board_build.embed_files` |
|
||
|
||
Replace `data/bg.gif` with any 360×360 GIF to change the background (keep it under ~3 MB).
|