mangavalkandClaude Opus 5.5
ad77b06c36
Robot-side firmware (Teensy 4.0) imported unchanged as extracted. platformio.ini defines [env:robot] (teensy40) and [env:remote] (teensy41); scripts/select_src_dir.py points each env at its own sketch folder so robot/ and remote/ stay Arduino-style sketches. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
52 lines
1.8 KiB
C++
52 lines
1.8 KiB
C++
#include "RobotIMU.h"
|
|
#include <Wire.h>
|
|
|
|
// MPU6050-style register map, default +/-2g / +/-250deg/s ranges.
|
|
// Swap readRaw() if you're using a different IMU part.
|
|
static constexpr uint8_t IMU_ADDR = 0x68;
|
|
static constexpr uint8_t REG_PWR_MGMT_1 = 0x6B;
|
|
static constexpr uint8_t REG_ACCEL_XOUT_H = 0x3B;
|
|
|
|
bool RobotIMU::begin() {
|
|
Wire.begin();
|
|
Wire.beginTransmission(IMU_ADDR);
|
|
Wire.write(REG_PWR_MGMT_1);
|
|
Wire.write(0x00); // wake the IMU out of sleep
|
|
ok_ = (Wire.endTransmission() == 0);
|
|
return ok_;
|
|
}
|
|
|
|
bool RobotIMU::readRaw(float& ax, float& ay, float& az, float& gx, float& gy, float& gz) {
|
|
Wire.beginTransmission(IMU_ADDR);
|
|
Wire.write(REG_ACCEL_XOUT_H);
|
|
if (Wire.endTransmission(false) != 0) return false;
|
|
Wire.requestFrom((int)IMU_ADDR, 14);
|
|
if (Wire.available() < 14) return false;
|
|
|
|
int16_t raw_ax = (Wire.read() << 8) | Wire.read();
|
|
int16_t raw_ay = (Wire.read() << 8) | Wire.read();
|
|
int16_t raw_az = (Wire.read() << 8) | Wire.read();
|
|
Wire.read(); Wire.read(); // skip temperature
|
|
int16_t raw_gx = (Wire.read() << 8) | Wire.read();
|
|
int16_t raw_gy = (Wire.read() << 8) | Wire.read();
|
|
int16_t raw_gz = (Wire.read() << 8) | Wire.read();
|
|
|
|
ax = raw_ax / 16384.0f; ay = raw_ay / 16384.0f; az = raw_az / 16384.0f;
|
|
gx = raw_gx / 131.0f; gy = raw_gy / 131.0f; gz = raw_gz / 131.0f; // deg/s
|
|
(void)gz;
|
|
return true;
|
|
}
|
|
|
|
void RobotIMU::update(float dt) {
|
|
if (!ok_ || !enabled) return;
|
|
float ax, ay, az, gx, gy, gz;
|
|
if (!readRaw(ax, ay, az, gx, gy, gz)) return;
|
|
|
|
float accel_roll = degrees(atan2(ay, az));
|
|
float accel_pitch = degrees(atan2(-ax, sqrt(ay * ay + az * az)));
|
|
|
|
constexpr float ALPHA = 0.98f; // trust the gyro short-term, the accelerometer long-term
|
|
roll_deg_ = ALPHA * (roll_deg_ + gx * dt) + (1 - ALPHA) * accel_roll;
|
|
pitch_deg_ = ALPHA * (pitch_deg_ + gy * dt) + (1 - ALPHA) * accel_pitch;
|
|
}
|