diff --git a/2019-teensy-nrf24/tests/teensy_mpu6050_test/teensy_mpu6050_test.ino b/2019-teensy-nrf24/tests/teensy_mpu6050_test/teensy_mpu6050_test.ino
new file mode 100644
index 0000000..734b521
--- /dev/null
+++ b/2019-teensy-nrf24/tests/teensy_mpu6050_test/teensy_mpu6050_test.ino
@@ -0,0 +1,82 @@
+/* LED Blink, Teensyduino Tutorial #1
+   http://www.pjrc.com/teensy/tutorial.html
+ 
+   This example code is in the public domain.
+*/
+#include <Wire.h>
+// Teensy 2.0 has the LED on pin 11
+// Teensy++ 2.0 has the LED on pin 6
+// Teensy 3.0 has the LED on pin 13
+const int ledPin = 13;
+
+// the setup() method runs once, when the sketch starts
+int reading = 0;
+int device = 104;
+
+void setup() {
+  // initialize the digital pin as an output.
+  pinMode(ledPin, OUTPUT);
+  Wire.begin(); // orange is clock, pin 19, yellow is data pin 18
+  Serial.begin(38400);
+  Wire.beginTransmission(device); // transmit to device
+  Wire.write(byte(0x6b));
+  Wire.write(byte(0x01));
+  
+  //Wire.write(byte(0x0D));
+  //Wire.write(byte(0x42));  // 
+  Wire.endTransmission();      // stop transmitting
+  
+}
+
+// the loop() methor runs over and over again,
+// as long as the board has power
+
+
+void loop() {
+     // set the LED on
+  //delay(2000);                  // wait for a second
+  //digitalWrite(ledPin, LOW);    // set the LED off
+  //delay(1000);                  // wait for a second
+  //Wire.beginTransmission(device); // transmit to device
+                               // the address specified in the datasheet is 224 (0xE0)
+                               // but i2c adressing uses the high 7 bits so it's 112
+  //Wire.write(byte(0x00));      // sets register pointer to the command register (0x00)  
+  //Wire.write(byte(0x50));      // command sensor to measure in "inches" (0x50) 
+                               // use 0x51 for centimeters
+                               // use 0x52 for ping microseconds
+  //Wire.endTransmission();      // stop transmitting
+
+  // step 2: wait for readings to happen
+  delay(70);                   // datasheet suggests at least 65 milliseconds
+
+  // step 3: instruct sensor to return a particular echo reading
+  Wire.beginTransmission(device); // transmit to device
+  //Wire.write(byte(0x75));      // ask who am i
+  Wire.write(byte(0x3B)); // X Acceleration High Bit
+  //Wire.write(byte(0x42));  // 
+  Wire.endTransmission();      // stop transmitting
+
+  // step 4: request reading from sensor
+  Wire.requestFrom(device, 1);    // request 2 bytes from slave device #112
+  
+  reading = Wire.read();  // receive high byte (overwrites previous reading)
+  Serial.println(reading);   // print the reading
+  if (reading > 150){
+    digitalWrite(ledPin, HIGH);
+    delay(100);
+    digitalWrite(ledPin, LOW);
+  }
+
+  // step 5: receive reading from sensor
+  
+  if(8 <= Wire.available())    // if bytes were received
+  {
+    reading = Wire.read();  // receive high byte (overwrites previous reading)
+    reading = reading << 8;    // shift high byte to be high 8 bits
+    reading |= Wire.read(); // receive low byte as lower 8 bits
+    Serial.println(reading);   // print the reading
+  }
+  
+
+  delay(50);                  // wait a bit since people have to read the output :)
+}